Leading 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Leading 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Do not ignore the forklift at the workplace. If the operation is not good, there will certainly be severe accidents in minutes, and there are numerous accidents including forklifts.

Situation 1: The forklift cargo blocked the motorist's view, and the individual ahead might not be discovered, leading to a rolling mishap.
Situation 2: In order to preserve the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift raises the workers illegally, the forklift vehicle driver does not wear the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the chauffeur should initially validate that the tons is secure and trustworthy.
4. The begin has to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake instantly while driving with lots unless there are unique conditions.
6. When the forklift is running, it must obey the web traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised other than when piling or filling. .
8. The elevation of the tons need to not block the motorist's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is forbidden for employees to base on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will certainly be fixed and reported in a timely fashion, and they will certainly never run with ailments or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork should be as deep as feasible under the load, and it ought to be noted that the fork pointer ought to not touch various other goods or items. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the driver does not leave the car's line of sight and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed Stand-on Electric Pallet Stacker in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive throughout the gradient. When the slope is above 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and most likely to the driver's line of vision, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the Electric Forklift Truck for Warehouse roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844